Tuesday, April 21, 2009

The printer spooler service not running message on pc screen

Question:-- The printer spooler service not running message on pc screen?
Answer:-- Ok if anyone cannot print or install a printer because it says The print spooler service is not running then follow these easy steps to get the service running as follows:--

1)click start
2)then control panel
3)then administrative Tools
4)then Services
5)then scroll down to print spooler
6)then right click it
7)then click properties
8)make sure you are on the general tab
9)then go down to startup type and make sure its on automatic
10)then hit apply
11)then click the start button under the service status
12)apply again
13)hit OK. 
now exit all of the services and administrative tools and go to where your printer and faxes  are located and now try to install a printer or try to print.This will help.

Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 


The printer words from the toner cartridge comes out as the hand is rubbed on the printed paper

Question:-- The printer words from the toner cartridge comes out as the hand is rubbed on the printed paper?
Answer:-- There are many possibilities .The most common are as follows:--
First, the fuser assembly may be damaged or at the end of its life. The solution is to replace the fuser assembly. Repairing a fuser assembly is generally not recommended because the fuser is considered a consumable printer part and not worth the time or effort to fix. Second, the toner cartridge may be defective and letting too much toner out at one time. In a black-and-white laser printer, the solution is to replace the toner cartridge. In a color laser printer, only replace the cartridge that is exhibiting the problem. Third, some toner may have spilled in the printer. If so, you'll need to clean it out.

Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 

The Printer is displaying a 50.4 error message

Question:-- The Printer is displaying a 50.4 error message?
Answer:-- The reason is as follows:-- A 50.4 error message on some of the newer HP LaserJet printers indicates a problem with the power supply.-------------
 If the printer is connected to a UPS, disconnect it, or disconnect it from a power strip and plug it directly into a wall outlet. A laser printer should never be plugged into a UPS, because the UPS can be damaged by the surges of power required by a printer to keep the fuser assembly warm. If that doesn’t work, make sure that all of the components in the printer are seated properly.this will help.


Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 

Why i Can't find a driver for a particular operating system

Question:-- Why i Can't find a driver for a particular operating system?
Answer:-- This is due to many reasons but mostly its due to as follows :--
Whenever the  new operating systems are released, new drivers will need to be loaded for your existing printers. Not all printers have a driver for every OS. In these cases, it’s best to consult the printer manual and find out what printers the drivers will emulate. While not all of the functionality of the printer will be available under this emulation, at least basic printing will work. For example, most HP printers will print with the HP LaserJet II driver installed, although specific options, such as duplexing, will not work.

Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 

The hp printer is displaying a 79 error on the display

Question:-- The hp Printer is displaying a 79 error?
Answer:- -- The cause :-----A 79 error can be the result of a problem with the network print server that services the printer. 
To resove the problem:--- When troubleshooting a 79 error, first open the Printer folder from the Start menu on the Print server to make sure there are no jobs pending. A 79 error can also indicate a failure of a printer add-on component, such as an MIO card or a RAM module. All add-ons should be removed and then added back to the printer one by one to determine which module may be at fault.

Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 

Thursday, April 16, 2009

Canon BJ F900 printer reset system

Question:-- How to reset Canon BJ F900 printer?
Answer:-- The system is as follows :--
Turn off the printer. 
Press and hold the RESUME button, then press and hold the POWER button. 
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily. 
You are now in Service mode. 
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press. 
1. service/factory test printout, including ink sensor check 
2. EEPROM info printout 
3. EEPROM initialization 
4. Clear the waste-ink counter 
5. Printer model setting. (more selections beyond this- leave this alone) 
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a rest.


Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 


Canon PIXMA IP3000 printer reset method

Question:-- How to reset Canon PIXMA IP3000 printer?
Answer:-- The procedure is as follows:--
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 

 

Canon S750 printer reset procedure

Question:-- How to reset Canon S750 printer?
Answer:--
  1. Turn off the printer.
  2. Press and hold the RESUME button, then press and hold the POWER button.
  3. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
  4. The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.
  5. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.

    1. Service/factory test printout, including ink sensor check
    2. EEPROM info printout
    3. EEPROM initialization
    4. Clear the waste-ink counter
    5. Printer model setting. (more selections beyond this- leave this alone)
     
  6. After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.

Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 


Canon S820 printer reset system

Question:-- How to reset Canon S820 printer ?
Answer:--
  1. Turn off the printer.
  2. Press and hold the RESUME button, then press and hold the POWER button.
  3. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
  4. The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.
  5. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.

    1. Service/factory test printout, including ink sensor check
    2. EEPROM info printout
    3. EEPROM initialization
    4. Clear the waste-ink counter
    5. Printer model setting. (more selections beyond this- leave this alone)
     
  6. After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.

 

Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

 


Reset procedure for canon ip 4000 printer

Question:-- how to reset waste ink counter of canon ip 4000

Answer:--- the procedure to reset waste ink counter of canon ip 4000 printer is as follows,read it carefully step by step:

1) With the printer power turned off, while pressing the Resume/Cancel button, 
press and hold the Power button. (DO NOT release the buttons. 
The LED lights in green to indicate that a function is selectable.) . 

2) While holding the Power button, release the Resume/Cancel button. (DO NOT 
release the Power button.) . 

3) While holding the Power button, press the Resume/Cancel button 2 times, and 
then release both the Power and Resume/Cancel buttons. 
(Each time the Resume/Cancel button is pressed, the LED lights alternately in 
orange and green, starting with orange.) . 

4) When the LED lights in green, press the Resume/Cancel button 4 times. (Each 
time the Resume/Cancel button is pressed, the LED lights 
alternately in orange and green, starting with orange.) . 

5) Press the Power button. The LED lights in green, and the reset is performed. 
(When the operation completes, the printer returns to the 
menu selection mode automatically.) . 

6) Press the power button to exit service mode. 

Note:- if you accidentally press the Resume/Cancel button more than 4 times in 
step 4 then just press the Resume/Cancel button at least 10 
times and the printer will be returned to step 4 automatically. 

BTW the other functions that are available at step 4 are - 
press 0 times = power off 
press 1 time = Service Test Print 
press 2 times = EEPROM information print 
press 3 times = EEPROM initialisation 
press 5 times = Destination settings (country information, do not play with 
this) 
press 6 times = Printhead Deep Cleaning 
press 7,8 or 9 times = not used in servicing so do not play with these. 
press 10 times or more = return to menu (step 4) 

Did you like this post? Why not leave a comment below or subscribe to my feed and get articles like this delivered automatically to your feed reader.

Friday, April 10, 2009

1988 Chevrolet S10 Radio Wiring

Radio wiring for 1988 Chevrolet S10


1988 Chevrolet S10 Pickup Truck Car Stereo Wiring Diagram

Radio Wiring
check out the wire colours in the list before connecting the wires also keep multimeter with you while connecting the wires to check out the exact voltage as mentioned in the list.


Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: Yellow
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Gray
Car Stereo Dimmer Wire: Brown
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: 4′ x 6′
Car Audio Front Speakers Location: Dash
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: 4′ x 10′
Car Audio Rear Speakers Location: Rear Corners
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue





ALSO READ THIS EXPERTS REPAIR EXPERIENCE:

AFTER INSTALLING SUBWOOFER RADIO WILL NOT WORK:


I installed a sub woofer and amp to the factory Delco radio/cd player IN 2001 S-10 Chevy Blazer. Everything is working fine, EXCEPT the lights on the radio/cd player DO NOT work if the key is turned one notch forward to the ON position, or if YOU start the engine. 
However,the lights on the radio/cd player DO work if YOU turn the key backwards to the ACC position. 


EXPERT'S REPLY:

Where did you connect the Red and Yellow power wires coming off the radio?
Please check this wires connection.

Customer's Reply To This Query:

It was factory radio, we unplug the wiring harness in the back and splice into the speaker wires. Then we simply plugged the harness back in to the radio. I'm assuming we did that correctly because the system itself sounds great, just no lights on that radio when key is in forward on position.

EXPERT'S REPLY:
Try moving the dash dimmer up and see if this makes a difference. Automatic headlights may be coming on which dims the display. Just plug the harness to the head lights back into the headlights switch on the dash.

This will Help.
Thanks.

ALSO VIEW THIS RELATED:

For Car parts and diagrams:

CAR MANUAL GUIDE
                 
FOR FREE MANUALS AND GUIDES: ---
Car repair guide?


For all types of car repair help:



Car Backfires

For car repair How to guides:


OVERHEATING: Radiator Fan Not Working

Engine Cooling Fan not Working


"Radiator fan"  "Engine Fan"  "COOLING FAN WILL NOT TURN OFF"

LIFT GATE / TAIL GATE ISSUES

TRUNK WILL NOT OPEN


CAR ALARM ISSUES


Car starter removal, Starter motor testing, Starter repairs, Starter solenoid, Starter wiring,


DOOR PANEL REMOVAL, car door panel, door panel components, front door panel, rear door panel,


HEATER CORE REPLACEMENT, HEATER CORE REMOVAL, TROUBLESHOOT HEATER CORE, FLUSH HEATER CORE,

CAR POWER SEAT, ELECTRIC SEAT, POWER SEAT WILL NOT WORK, SEAT WILL NOT GO FORWARD,



For all types of---------

Timing belt routing diagrams for cars and trucks?



                          

==========

For all types of --------

Drive belt routing diagrams for cars and trucks?




stalling issues:
Engine stalls, car stalls while starting, vehicle stalls while starting, Engine stalls and dies, Car stalls and stops,


CRUISE CONTROL Not working, cruise control replacing, troubleshooting cruise control problems,


TRANSMISSION PROBLEMS:

NO REVERSE ON TRANSMISSION

GEAR SHIFT ISSUES

Transmission fluid leak, transmission gears slip,


TRANSMISSION REPLACING AND TROUBLESHOOTING, INSPECTING TRANSMISSION COMPONENTS, TRANSMISSION FAILURES, OD WARNING LIGHT,


TRANSMISSION FLUID FILLING, WHERE TO FILL TRANSMISSION FLUID, AUTOMATIC TRANSMISSION FLUID, NO TRANSMISSION DIPSTICK,


WINDSHIELD WIPERS, WINDSHIELD WIPERS NOT WORKING,WIPER MOTOR MAKING NOISE,NO WIPERS,WIPER FLUID LEAKS,WIPER FUSE AND RELAY,


COOLANT LEAK ISSUES, COOLANT LEAK PROBLEMS, COOLANT SENSOR, LOW COOLANT,


BRAKE LIGHTS NOT WORKING, REPAIRING BRAKE LIGHTS, NO BRAKE LIGHTS,


CHECK ENGINE LIGHT,ENGINE WARNING LIGHT FLASHING,ENGINE LIGHT ON DASH,DASHBOARD WARNING LIGHT,ECM ERROR CODES,


DASHBOARD WARNING LIGHTS ARE ON, ENGINE LIGHT ON DASH,WARNING LIGHTS STEADY ON DASH,RESET DASH BOARD WARNING INDICATOR,


KEYFOB PROGRAMMING, REPROGRAMMING CAR KEY, KEYLESS ENTRY RESET,ANTITHEFT WILL NOT LET CAR TO START, ANTI THEFT ISSUES, KEYFOB NOT WORKING, KEYLESS ENTRY QUIT WORKING,


IGNITION KEY WILL NOT RELEASE, IGNITION KEY STUCK UP, KEY WILL NOT COME OUT OF IGNITION, FAULTY IGNITION KEY LOCK CYLINDER, REPLACING IGNITION CYLINDER,


HEATER ISSUES:

HEATER NOT BLOWING COLD,NO HOT AIR FROM HEATER,A/C BLOWS HOT AIR,A/C NOT BLOWING COLD, COLD AIR FROM HEATER,BLEND DOOR ACUTATOR CLOSED,HVAC UNIT NOT OPERATING,



HEATER NOT BLOWING COLD,NO HOT AIR FROM HEATER,A/C BLOWS HOT AIR,A/C NOT BLOWING COLD, COLD AIR FROM HEATER,BLEND DOOR ACUTATOR CLOSED,HVAC UNIT NOT OPERATING,



STEERING ISSUES:

POWER STEERING TROUBLESHOOTING, STEERING SQUEAKS, POWER STEERING FLUID LEAKS, FAULTY POWER STEERING PUMP, POWER STEERING NOT WORKING, POWER STEERING BELT,



VEHICLE STARTING ISSUE:

CAR NO START: ENGINE NOT TURNING OVER:

max