Tuesday, March 22, 2011

p0411 on chevy trailblazer?

Click this link for complete service bulletin details:----
-----------------


The service bulletin:----
TSB SB06-03-S004 Diagnostic Information For Finding A Restriction Or Leak At Secondary Air
Injection (SAI) System Inlet Or Outlet Hoses
Diagnostic Information For Finding A Restriction Or Leak At Secondary Air Injection (SAI) System Inlet Or
Outlet Hoses
ISSUE DATE: OCTOBER 2006
Affected Vehicles
2006-2007 Isuzu Ascender (US/UT) with 4.2L Engine
Service Information
IMPORTANT: The information provided in this Service Bulletin will aid ONLY in diagnosing a restriction or
leak in the SAI system inlet or outlet hoses that cannot be detected by blowing shop air through them.
When diagnosing a Malfunction Indicator Lamp (MIL) light illuminated on the instrument cluster, technicians
may find that the vehicle has previously been serviced for this same condition. Technicians may also find a
DTC P0411, which may have led to previous SAI system component replacements.
A (MIL) light illuminated due to P0411 -- The diagnostic has detected a SAI system insufficient airflow due to
a malfunctioning:
• SAI system check valve
• SAI system pump
• SAI system relay and related control circuit
• SAI system inlet or outlet hose restriction or leak
The information provided in this Service Bulletin will aid only in diagnosing a restriction or leak in the SAI
system inlet or outlet hoses that cannot be detected by blowing shop air through them. Be sure to follow the
diagnostic information outline for DTC P0411 in the Service Manual. The following information provided in
this bulletin will be used in conjunction with the Service Manual.
Service Procedure
SAI SYSTEM INLET AND OUTLET HOSE ASSEMBLY
1. Air Shut-Off Valve
2. Inlet Hose to Air Cleaner
3. Retaining Bolt
4. Outlet Hose to Air Distribution Manifold
5. Air Pump
6. Inlet Hose to Air Distribution Manifold
7. Air Distribution Manifold and Retaining Bracket
8. Outlet Hose to Air Shut-Off Valve .



IMPORTANT: Due to the complexity of these procedures, the following repair steps must be strictly adhered
to in order to achieve the intended results. Any deviation or substitution may result in a sub-standard repair
resulting in a repeat DTC P0411.
IMPORTANT: Refer to and copy all of the appropriate sections of the Service Manual repair procedures
before attempting this repair.
Before using the following information outline in this bulletin service procedure, Refer to DTC P0411
Diagnostic in the Service Manual diagnostic information for DTC P0411 in the Service Manual has been
followed and led to a restriction or leak.
The following information provided in this bulletin will further assist in diagnosing an SAI system inlet or outlet
hose restriction or leak concern.
IMPORTANT: Additional Diagnostic Information on Secondary Air Injection (SAI) Systems can be founding
IsuzuONE.com Service News “2005-06 Secondary Air Injection (SAI) Systems”.
When diagnosing the concern of a restriction or leak at the SAI system hoses, a normal reading of 20-25 kPa
above BARO may be noted with the SAI system pump ON and the SAI system solenoid OFF. However, with
the SAI system solenoid enabled, it may be noted that the SAI system pressure sensor parameter is not 8-12
kPa above the BARO reading, indicating an insufficient air flow condition has been detected due to a
restriction or leak in the SAI system inlet or outlet hoses. The following diagnostic procedure determines if the
SAI system is operating as designed:
SAI SYSTEM DIAGNOSTIC VERIFICATION
1. Start and idle the engine for about 2 minutes to allow the SAI system diagnostic to run and complete.
2. The start-up coolant and ambient air temperatures have to be in the specified operating range.
3. SAI system pressure parameter should be BARO with a Tech 2.
4. Command the SAI system air pump relay ON. The SAI system air pump should operate. The Tech 2
parameter will indicate only that the SAI system air pump relay is commanded ON. The pump should be
dead-headed so the expected pressure would increase to a range of 18-25 kPa above BARO.
5. Command the SAI system air shut-off valve solenoid relay ON. The SAI system air pump should operate
and the SAI system solenoid / check valve should open. The Tech 2 parameter will indicate that both SAI
system relays are commanded ON. With the pump ON and the valve open, the expected pressure would
increase to a range of 8-12 kPa above BARO.
6. After opening the valve in step 5, the pressure should decrease from the value read in step 4, but should
not decrease all the way to the value read in step 3. . The difference in readings between step 3 and step 5
should be greater than 8 kPa and in the range of 8-12 kPa. If the difference in readings between steps 3 and
5 is less than 8 kPa, this might be due to a restriction or leak in the SAI system but other possible root causes
may exist. If this difference is less than 8 kPa, proceed to step number 7.
If this difference is greater than 8 kPa, review the scan tool DTC information and refer to the Service Manual
for further service procedures.
7. Temporarily remove the SAI system inlet hose from the SAI system air pump and enable the SAI system
air shut-off valve solenoid with the Tech 2. If the SAI system pressure sensor parameter increases to 8-12
kPa above the BARO reading, the SAI system inlet hose is restricted and the SAI system inlet and outlet
hose assembly should be replaced. If the SAI system pressure sensor parameter is not 8-12 kPa above the
BARO reading, proceed to step number 8 of the SAI verification diagnostic procedure.
8. Temporarily substitute a 25.4 mm (1 in) O.D length of standard hose and route the hose from the SAI
system air pump outlet to the SAI system air shut-off valve solenoid making sure that there are no kinks in the
hose. Enable the SAI system air shut-off valve solenoid with the Tech 2. If the air pressure sensor parameter
increases to 8-12 kPa above the BARO reading, the SAI system outlet hose is restricted and the SAI system
Inlet and Outlet Hose Assembly should be replaced.
9. Install an SAI system Inlet and Outlet Hose Assembly, P/N 8-10373-307-0, with Retaining Bolt, P/N
8-11519-861-0 (M10 X 1.5 X 30), using the following procedures:
IMPORTANT: Refer to and copy all of the appropriate sections of the Service Manual repair procedures
before attempting this repair.
REMOVAL PROCEDURE - SAI SYSTEM INLET AND OUTLET HOSE ASSEMBLY
1. Relieve the fuel pressure. Refer to Fuel Pressure Relief Procedure in the Service Manual.
2. Disconnect the negative battery cable at the battery.
3. Raise the vehicle. Refer to Lifting and Jacking the vehicle in the Service Manual.
4. Disconnect inlet and outlet hoses from the SAI system air pump.
5. Remove the inlet and outlet hoses and retainer clip from the frame.
6. Lower the vehicle.
3/77. Disconnect the SAI system inlet hose from air cleaner.
8. Remove the air cleaner outlet resonator. Refer to Air Cleaner Outlet Resonator Replacement in the Service
Manual.
9. Disconnect the SAI system outlet hose from the air shut-off valve.
IMPORTANT: The Throttle Body Assembly does not have to be removed when removing the Intake Manifold.
10. Remove intake manifold. Refer to Intake Manifold Replacement in the Service Manual.
11. Remove the engine coolant temperature (ECT) harness connector.
12. Disconnect cylinder number 6 ignition coil engine harness connector.
13. Remove the retaining bolt from the ignition coil.
14. Remove the ignition coil from the engine.
15. Remove the retaining bolt (M10 X 1.5 X 30) and fir-tree fastener securing the SAI system Inlet and Outlet
Hose Assembly to the rear of the engine cylinder head by using the following procedure:
• Access the bolt by laying over the top of the engine.
• Using a 15 mm standard length offset box end wrench, loosen the bolt.
• Then use a short handle combination ratcheting box/open end 15 mm wrench to remove the bolt from the
back of the cylinder head.
• Once the bolt is removed from the engine cylinder head, the bolt will stay attached to the Air Distribution
Manifold and Retaining Bracket. The fir-tree fastener will release itself from the back of the engine cylinder
head by pushing back toward the cowl on the Air Distribution Manifold and Retaining Bracket.
16. Remove the SAI System Inlet and Outlet Hose Assembly by working the Air Distribution Manifold and
Retaining Bracket in a back and forth upward motion past the back of the engine cylinder head via the cowl.
Once the complete assembly has past the back of the cam cover, continue to work the SAI System Inlet and
Outlet Hose Assembly out of the engine compartment. Refer to the below.

max