Saturday, April 9, 2011

toyota landcruiser gxl Wheel torque setting?

  1. Tighten the adjusting nut to 43 ft. lbs. (59 Nm) while rotating the hub to seat the bearings.
  2. Loosen the adjusting nut.
  3. Tighten the adjusting nut to 48 inch lbs. (5.4 Nm) and check that the bearing has no play.
  4. Check the bearing preload with a spring tension gauge. The preload should be 6.4-12.6 lbs. (28-56 N) for 2001-03; 9.5-15 lbs. (42-67 N)


  1. Install or connect the following:

    Lockwasher
    Locknut. Tighten the nut to 47 ft. lbs. (64 Nm). Recheck the preload.
    Hub drive flange. Tighten the nuts to 26 ft. lbs. (35 Nm) for 2001-03; 24 ft. lbs. (33 Nm) for 2004 and above.
    Snapring. Pull out on the axle shaft and select a snapring that ensures that the clearance between the tip of the flange and the snapring is less than 0.008 inch (0.2mm).
    Grease cap
    Brake caliper
    Front wheel


The wheel bearings are sealed unit; no adjustment is possible.

The wheel bearings are sealed unit; no adjustment is possible.

  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:

    Front wheel
    Brake caliper
    Grease cap
    Snapring
    Hub drive flange
    Locknut
    Lock washer

  3. Tighten the adjusting nut to 43 ft. lbs. (59 Nm) while rotating the hub to seat the bearings.
  4. Loosen the adjusting nut.
  5. Tighten the adjusting nut to 48 inch lbs. (5.4 Nm) and check that the bearing has no play.
  6. Check the bearing preload with a spring tension gauge. The preload should be 6.4-12.6 lbs. (28-56 N) for 2002-03; 9.5-15 lbs. (42-67 N) for 2004-06.
  7. Install or connect the following:

    Lock washer
    Locknut. Tighten the nut to 47 ft. lbs. (64 Nm). Recheck the preload.
    Hub drive flange. Tighten the nuts to 26 ft. lbs. (35 Nm) for 2002-03; 24 ft. lbs. (33 Nm) for 2004-06.
    Snapring. Pull out on the axle shaft and select a snapring that ensures that the clearance between the tip of the flange and the snapring is less than 0.008 inch (0.2mm).
    Grease cap
    Brake caliper
    Front wheel


The wheel bearings are sealed unit; no adjustment is possible.

Removal & Installation



  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheel
    Brake caliper
    Grease cap
    Snapring
    Hub drive flange
    Locknut
    Lockwasher
    Adjusting nut
    Outer bearing
    Wheel hub
    Inner grease seal
    Inner bearing


To install:

  1. Install or connect the following:

    Inner bearing
    Inner grease seal
    Wheel hub
    Outer bearing
    Adjusting nut. Adjust the wheel bearings.
    Lockwasher
    Locknut. Tighten the nut to 47 ft. lbs. (64 Nm).
    Hub drive flange. Tighten the nuts to 26 ft. lbs. (35 Nm).
    Snapring
    Grease cap
    Brake caliper
    Front wheel



  2. Click image to see an enlarged view

    Fig. Exploded view of the front hub and related components-LX470


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheel
    Brake caliper
    Grease cap
    Snapring
    Hub drive flange
    Locknut
    Lockwasher
    Adjusting nut
    Outer bearing
    Wheel hub
    Inner grease seal
    Inner bearing


To install:

  1. Install or connect the following:

    Inner bearing
    Inner grease seal
    Wheel hub
    Outer bearing
    Adjusting nut. Adjust the wheel bearings.
    Lockwasher
    Locknut. Tighten the nut to 47 ft. lbs. (64 Nm).
    Hub drive flange. Tighten the nuts to 26 ft. lbs. (35 Nm) for 2001-03; 24 ft. lbs. (33 Nm) for 2004.
    Snapring
    Grease cap
    Brake caliper
    Front wheel



  2. Click image to see an enlarged view

    Fig. Exploded view of the front hub and related components-2001 Land Cruiser



    Click image to see an enlarged view

    Fig. Exploded view of the front hub and related components-2004 Land Cruiser




Click image to see an enlarged view

Fig. Front hub and related parts-Sequoia

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheel
    Grease cap
    With 4wd, cotter pin, lock cap and halfshaft nut
    Speed sensor wire from the knuckle
    Caliper and rotor. Support the caliper out of the way.
    Lower ball joint
    Axle hub/steering knuckle assembly and place it in a vise
    With 2wd, the grease cap
    Inner grease seal, for 4WD

  3. Remove the 4 bolts and shift the dust cover towards the hub side.
  4. Using a suitable puller, remove the hub from the knuckle.
  5. Remove the dust cover from the steering knuckle.
  6. With 4wd, remove the bearing spacer and Anti-lock Brake System (ABS) speed sensor, if equipped with ABS


WARNING
Be careful not to scratch the speed sensor rotor serrations.

  1. Remove the outside oil seal from steering knuckle, using a small prybar
  2. Remove the bearing from the steering knuckle, as follows:

    Snapring
    Bearing from the steering knuckle, using tools 09950-60020 and 09950-70010, or equivalent.


To install:

  1. Install the bearing to the steering knuckle, as follows:

    Bearing to the steering knuckle, using a press and tools 09950-60020 and 09527-17011, or equivalent
    New snapring

  2. Install the new outside oil seal to steering knuckle, using a plastic hammer and tools 09223-15030 and 09527-17011. Coat the seal lip with MP grease.
  3. Install the axle hub to the steering knuckle, as follows:

    Dust cover to the steering knuckle. Torque the 4 bolts to 13 ft. lbs. (18 Nm).
    Axle hub to the steering knuckle, using a shop press and tool 09649-17010, or equivalent.

  4. Install or connect the following:

    Bearing spacer and Anti-lock Brake System (ABS) speed sensor, if equipped with ABS



WARNING
Be careful not to scratch the speed sensor rotor serrations.



Bearing spacer, if not equipped with ABS, using a shop press and tools 09950-60010 and 09950-70010
With 2wd, install a new locknut. Torque to 203 ft. lbs. (274 Nm). Stake the nut.
With 4wd, the bearing spacer using a press
Grease cap, for 2WD
Inner grease seal, for 4WD, using a plastic hammer and tool 09527-17011

  1. Install the hub/steering knuckle assembly. With 4wd, install the halfshaft and install the nut loosely.
  2. Connect the knuckle to the upper arm. Torque the nut to 77 ft. lbs. (105 Nm). The nut can be tightened up to an additional 60 degrees to align the hole. Install a new cotter pin.
  3. Connect the lower ball joint. Torque the 4 bolts to 48 ft. lbs. (65 Nm).
  4. Install the shock absorber.
  5. Install the rotor and caliper.
  6. Attach the brake line to the knuckle.
  7. Connect the speed sensor.
  8. With 4wd, apply the brakes and tighten the shaft nut to 173 ft. lbs. (235 Nm). The nut can be tightened up to an additional 60 degrees to align the hole. Install a new cotter pin.
  9. Install the grease cap.
  10. Install the wheel.
  11. Check the alignment.

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:

    Front wheel
    Axle hub/steering knuckle assembly and place it in a vise
    Grease cap, for 2WD
    Inner grease seal, for 4WD

  3. Remove the axle hub from the steering knuckle
    WARNING
    Be careful not to scratch the speed sensor rotor serrations.



    4 bolts and shift the dust cover towards the outside (hub side)
    Axle hub from the steering knuckle, using tools 09710-30021 and 09950-40011
    Dust cover from the steering knuckle
    Bearing spacer and Anti-lock Brake System (ABS) speed sensor, if equipped with ABS
    Spacer, if not equipped with ABS

  4. Remove the outside oil seal from steering knuckle, using a small prybar
  5. Remove the bearing from the steering knuckle, as follows:

    Snapring
    Bearing from the steering knuckle, using tools 09950-60020 and 09950-70010


To install:

  1. Install the bearing to the steering knuckle, as follows:

    Bearing to the steering knuckle, using tools 09950-60020 and 09527-17011
    Snapring

  2. Install the new outside oil seal to steering knuckle, using a plastic hammer and tools 09223-15030 and 09527-17011
  3. Install the axle hub to the steering knuckle, as follows:

    Dust cover to the steering knuckle. Torque the 4 bolts to 13 ft. lbs. (18 Nm).
    Axle hub to the steering knuckle, using a shop press and tool 09649-17010

  4. Install or connect the following:
    WARNING
    Be careful not to scratch the speed sensor rotor serrations.



    Bearing spacer and Anti-lock Brake System (ABS) speed sensor, if equipped with ABS



    Bearing spacer, if not equipped with ABS, using a shop press and tools 09950-60010 and 09950-70010
    Grease cap, for 2WD
    Inner grease seal, for 4WD, using a plastic hammer and tool 09527-17011
    Axle hub/steering knuckle assembly
    Front wheel


  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:

    Front wheel
    Brake caliper
    Grease cap
    Snapring
    Hub drive flange
    Locknut
    Lock washer
    Adjusting nut
    Outer bearing
    Wheel hub
    Inner grease seal
    Inner bearing


To install:

  1. Install or connect the following:

    Inner bearing
    Inner grease seal
    Wheel hub
    Outer bearing
    Adjusting nut. Adjust the wheel bearings.
    Lock washer
    Locknut. Tighten the nut to 47 ft. lbs. (64 Nm).
    Hub drive flange. Tighten the nuts to 26 ft. lbs. (35 Nm) for 2002-03; 24 ft. lbs. (33 Nm) for 2004-06.
    Snapring
    Grease cap
    Brake caliper
    Front wheel

    Click image to see an enlarged view

    Fig. Exploded view of the front hub and related components-2002 Land Cruiser



    Click image to see an enlarged view

    Fig. Exploded view of the front hub and related components-2004-06 Land Cruiser





Click image to see an enlarged view

Fig. Front hub and related parts-Sequoia

  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:

    Front wheel
    Grease cap
    With 4wd, cotter pin, lock cap and halfshaft nut
    Speed sensor wire from the knuckle
    Caliper and rotor. Support the caliper out of the way.
    Lower ball joint
    Axle hub/steering knuckle assembly and place it in a vise
    With 2wd, the grease cap
    Inner grease seal, for 4WD

  3. Remove the 4 bolts and shift the dust cover towards the hub side.
  4. Using a suitable puller, remove the hub from the knuckle.
  5. Remove the dust cover from the steering knuckle.
  6. With 4wd, remove the bearing spacer and Anti-lock Brake System (ABS) speed sensor, if equipped with ABS
    WARNING
    Be careful not to scratch the speed sensor rotor serrations.

  7. Remove the outside oil seal from steering knuckle, using a small prybar
  8. Remove the bearing from the steering knuckle, as follows:

    Snapring
    Bearing from the steering knuckle, using tools 09950-60020 and 09950-70010, or equivalent.


To install:

  1. Install the bearing to the steering knuckle, as follows:

    Bearing to the steering knuckle, using a press and tools 09950-60020 and 09527-17011, or equivalent
    New snapring

  2. Install the new outside oil seal to steering knuckle, using a plastic hammer and tools 09223-15030 and 09527-17011. Coat the seal lip with MP grease.
  3. Install the axle hub to the steering knuckle, as follows:

    Dust cover to the steering knuckle. Torque the 4 bolts to 13 ft. lbs. (18 Nm).
    Axle hub to the steering knuckle, using a shop press and tool 09649-17010, or equivalent.

  4. Install or connect the following:
    WARNING
    Be careful not to scratch the speed sensor rotor serrations.



    Bearing spacer and Anti-lock Brake System (ABS) speed sensor, if equipped with ABS



    Bearing spacer, if not equipped with ABS, using a shop press and tools 09950-60010 and 09950-70010
    With 2wd, install a new locknut. Torque to 203 ft. lbs. (274 Nm). Stake the nut.
    With 4wd, the bearing spacer using a press
    Grease cap, for 2WD
    Inner grease seal, for 4WD, using a plastic hammer and tool 09527-17011

  5. Install the hub/steering knuckle assembly. With 4wd, install the halfshaft and install the nut loosely.
  6. Connect the knuckle to the upper arm. Torque the nut to 77 ft. lbs. (105 Nm). The nut can be tightened up to an additional 60 degrees to align the hole. Install a new cotter pin.
  7. Connect the lower ball joint. Torque the 4 bolts to 48 ft. lbs. (65 Nm).
  8. Install the shock absorber.
  9. Install the rotor and caliper.
  10. Attach the brake line to the knuckle.
  11. Connect the speed sensor.
  12. With 4wd, apply the brakes and tighten the shaft nut to 173 ft. lbs. (235 Nm). The nut can be tightened up to an additional 60 degrees to align the hole. Install a new cotter pin.
  13. Install the grease cap.
  14. Install the wheel.
  15. Check the alignment.

---------------------------------
SPECIFICATIONS:------------

TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandardOptionalFrontRear
2002Land CruiserP275/70R16None29A32A8-JJ-97
SequoiaP245/70R16P265/70R1632Std: 35; Opt: 327-JJ-83
1PSI: Pounds Per Square Inch
2- Trailer towing: front 32; rear 35
3- Upper ball joint turning torque: 6-39 inch lbs.
4- See placard on vehicle
TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandardOptionalFrontRear
2003Land CruiserP275/65R17P275/60R18--8-JJ-97
SequoiaP265/70R16P265/6R1732Std: 35; Opt: 327-JJ-83
1PSI: Pounds Per Square Inch
2- Trailer towing: front 32; rear 35
3- Upper ball joint turning torque: 6-39 inch lbs.
4- See placard on vehicle
TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandardOptionalFrontRear
2004Land CruiserP275/65R17P275/60R18--8-JJ-97
SequoiaP265/70R16P265/65R17--std: 7; opt: 7.5-83
1PSI: Pounds Per Square Inch
2- Trailer towing: front 32; rear 35
3- Upper ball joint turning torque: 6-39 inch lbs.
4- See placard on vehicle


Click image to see an enlarged view

Fig.

TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandartOptionalFrontRear
2001Land CruiserP275/70R16None29A32A8-JJ-97
SequoiaP245/70R16P265/70R1632Std: 35; Opt: 327-JJ-83

Right click on the chart image and select option "open image in new web" if the chart image is not seen full or its very small to see.-----------

1OEM: Original Equipment Manufacturer
2- Trailer towing: front 32; rear 35
3- Replace if any measurable movement is found.
4- Upper ball joint turning torque: 6-39 inch lbs.
5- Upper arm ball joint turning torque: 40 inch lbs. or less
6- Upper arm ball joint turning torque: 9-39 inch lbs.
7- See placard on vehicle
TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandartOptionalFrontRear
2002Land CruiserP275/70R16None29A32A8-JJ-97
SequoiaP245/70R16P265/70R1632Std: 35; Opt: 327-JJ-83
1OEM: Original Equipment Manufacturer
2- Trailer towing: front 32; rear 35
3- Replace if any measurable movement is found.
4- Upper ball joint turning torque: 6-39 inch lbs.
5- Upper arm ball joint turning torque: 40 inch lbs. or less
6- Upper arm ball joint turning torque: 9-39 inch lbs.
7- See placard on vehicle
TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandartOptionalFrontRear
2003Land CruiserP275/65R17P275/60R18--8-JJ-97
SequoiaP265/70R16P265/6R1732Std: 35; Opt: 327-JJ-83
1OEM: Original Equipment Manufacturer
2- Trailer towing: front 32; rear 35
3- Replace if any measurable movement is found.
4- Upper ball joint turning torque: 6-39 inch lbs.
5- Upper arm ball joint turning torque: 40 inch lbs. or less
6- Upper arm ball joint turning torque: 9-39 inch lbs.
7- See placard on vehicle
TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandartOptionalFrontRear
2004Land CruiserP275/65R17P275/60R18--8-JJ-97
SequoiaP265/70R16P265/65R17--std: 7; opt: 7.5-83
1OEM: Original Equipment Manufacturer
2- Trailer towing: front 32; rear 35
3- Replace if any measurable movement is found.
4- Upper ball joint turning torque: 6-39 inch lbs.
5- Upper arm ball joint turning torque: 40 inch lbs. or less
6- Upper arm ball joint turning torque: 9-39 inch lbs.
7- See placard on vehicle
TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandartOptionalFrontRear
2005Land CruiserP275/65R17P275/60R18--8-JJ-97
SequoiaP265/70R16P265/65R17--std: 7; opt: 7.5-83
1OEM: Original Equipment Manufacturer
2- Trailer towing: front 32; rear 35
3- Replace if any measurable movement is found.
4- Upper ball joint turning torque: 6-39 inch lbs.
5- Upper arm ball joint turning torque: 40 inch lbs. or less
6- Upper arm ball joint turning torque: 9-39 inch lbs.
7- See placard on vehicle
TIRE, WHEEL AND BALL JOINT SPECIFICATIONS
YearModelOEM TiresTire Pressure (psi)Wheel SizeBall Joint InspectionLugnut Torque (ft. lbs.)
StandartOptionalFrontRear
2006Land CruiserP275/65R17P275/60R18--8-JJ-97
SequoiaP265/70R16P265/65R17--std: 7; opt: 7.5-83
1OEM: Original Equipment Manufacturer
2- Trailer towing: front 32; rear 35
3- Replace if any measurable movement is found.
4- Upper ball joint turning torque: 6-39 inch lbs.
5- Upper arm ball joint turning torque: 40 inch lbs. or less
6- Upper arm ball joint turning torque: 9-39 inch lbs.
7- See placard on vehicle.


--------------------
WHEEL ALIGNMENT:----
WHEEL ALIGNMENT
YearModelCasterCamberToe-in (in.)Steering Axis Inclination (Dec.)
Range (+/- Deg.)Preferred Settings (Deg.)Range (+/- Deg.)Preferred Settings (Deg.)
2002Land Cruiser0.752.50.750.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.750.130.05+/-0.0810.635+/-0.75
1- P245/70R16: +2.95
WHEEL ALIGNMENT
YearModelCasterCamberToe-in (in.)Steering Axis Inclination (Dec.)
Range (+/- Deg.)Preferred Settings (Deg.)Range (+/- Deg.)Preferred Settings (Deg.)
2003Land Cruiser0.752.50.750.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.750.130.05+/-0.0810.635+/-0.75
1- P245/70R16: +2.95
WHEEL ALIGNMENT
YearModelCasterCamberToe-in (in.)Steering Axis Inclination (Dec.)
Range (+/- Deg.)Preferred Settings (Deg.)Range (+/- Deg.)Preferred Settings (Deg.)
2004Land Cruiser0.752.50.750.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.750.130.05+/-0.0810.635+/-0.75
1- P245/70R16: +2.95


Click image to see an enlarged view

Fig.

WHEEL ALIGNMENT
YearModelCasterCamberToe-in (in.)Steering Axis Inclination (Deg.)
Range (+/- Deg.)Preferred Settings (Deg.)Range (+/- Deg.)Preferred Settings (Deg.)
2001Land Cruiser0.75+2.500.75+0.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.75+0.130.05+/-0.0810.635+/-0.75
1Note: All algnment specifications are based on nominal ride height and standard tires
2- P245/70R16: +2.95
WHEEL ALIGNMENT
YearModelCasterCamberToe-in (in.)Steering Axis Inclination (Deg.)
Range (+/- Deg.)Preferred Settings (Deg.)Range (+/- Deg.)Preferred Settings (Deg.)
2002Land Cruiser0.75+2.500.75+0.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.75+0.130.05+/-0.0810.635+/-0.75
1Note: All algnment specifications are based on nominal ride height and standard tires
2- P245/70R16: +2.95
WHEEL ALIGNMENT
YearModelCasterCamberToe-in (in.)Steering Axis Inclination (Deg.)
Range (+/- Deg.)Preferred Settings (Deg.)Range (+/- Deg.)Preferred Settings (Deg.)
2003Land Cruiser0.75+2.500.75+0.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.75+0.130.05+/-0.0810.635+/-0.75
1Note: All algnment specifications are based on nominal ride height and standard tires
2- P245/70R16: +2.95
WHEEL ALIGNMENT
YearModelCasterCamberToe-in (in.)Steering Axis Inclination (Deg.)
Range (+/- Deg.)Preferred Settings (Deg.)Range (+/- Deg.)Preferred Settings (Deg.)
2004Land Cruiser0.75+2.500.75+0.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.75+0.130.05+/-0.0810.635+/-0.75
1Note: All algnment specifications are based on nominal ride height and standard tires
2- P245/70R16: +2.95
WHEEL ALIGNMENT
YearModelCasterCamberToe-in (in.)Steering Axis Inclination (Deg.)
Range (+/- Deg.)Preferred Settings (Deg.)Range (+/- Deg.)Preferred Settings (Deg.)
2005Land Cruiser0.75+2.500.75+0.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.75+0.130.05+/-0.0810.635+/-0.75
2005Land Cruiser0.75+2.500.75+0.080.04+/-0.0812.17+/-0.75
Sequoia0.75A0.75+0.130.05+/-0.0810.635+/-0.75
1Note: All algnment specifications are based on nominal ride height and standard tires
2- P245/70R16: +2.95

----------------