Thursday, September 22, 2011

How to replace Intake Manifold on 2001 Audi A4?

Intake Manifold


Removal & Installation



1.8L Engine
  1. Turn the ignition switch to the OFF , then disconnect the negative battery cable.
  2. Remove the engine covers.
  3. Drain the engine coolant into a sealable container.
  4. Disconnect the hose for the Leak Detection Pump (LDP).
  5. Disconnect the accelerator pedal cable from the throttle valve control module.
  6. Remove the air guide hose from the throttle valve control module.
  7. Disconnect the vacuum line from the Evaporative Emissions (EVAP) canister.
  8. Detach the brake booster vacuum hose.
  9. Disconnect the Intake Air Temperature (IAT) sensor and the throttle valve control module.
  10. Detach the Camshaft Position (CMP) sensor wiring harness connector.
  11. Properly relieve the fuel system pressure.
  12. Disconnect the fuel rail with the injectors and position it aside in the engine compartment on a clean cloth.
  13. Disconnect the coolant hoses attached to the intake manifold.
  14. Disconnect the crankcase breather hose at the intake manifold.
  15. Remove the intake manifold brace and the oil dipstick.
  16. Unbolt the manifold at the mounting flange, then remove.
  17. Stuff clean shop rags into the cylinder head ports to prevent debris from entering the engine.
  18. Clean all gasket surfaces of any old gasket material.

To install:

  1. Remove the rags from the cylinder head ports.
  2. Install the intake manifold with new gaskets and tighten the mounting fasteners to 84 inch lbs. (10 Nm).
  3. Connect the manifold brace and tighten the bracket mounting bolts to 15 ft. lbs. (20 Nm).
  4. Install the dipstick.
  5. Connect the crankcase breather and coolant hoses to the intake manifold.
  6. Replace the fuel injector sealing O-rings, lubricate the O-rings with a light coating of fresh engine oil, then install the fuel rail with the injectors and tighten the retaining bolts to 88 inch lbs. (10 Nm).
  7. Connect the CMP and the IAT sensors to the throttle valve control module.
  8. Connect the brake booster and EVAP canister vacuum hoses.
  9. Connect the air guide hose and the accelerator pedal cable to the throttle valve control module.
  10. Connect the hose for the LDP.
  11. Top off the engine coolant and bleed as necessary.
  12. Reconnect the negative battery cable.
  13. Fully close all power windows to stop, operate all window switches for at least 1 second in the close direction to activate the 1-touch opening/closing function.
  14. Check the oil level before starting the engine, and top off as necessary.
  15. Enter the radio security code.
  16. Set the clock to the correct time.


NOTE
Diagnostic Trouble Codes (DTCs) may be stored when harness connectors are detached.

  1. Read the DTCs and clear the fault codes.



Click image to see an enlarged view

Fig. To remove the crimped vacuum hose clamp, first insert a suitable pick tool into the crimped opening, then . . .



Click image to see an enlarged view

Fig. . . . move the pick from side . . .



Click image to see an enlarged view

Fig. . . . to side while pressing inward on the pick. If necessary insert a small flat blade screwdriver and repeat the process until the clamp is sufficiently loose. Once removed, replace the clamp

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine coolant.
  3. Properly relieve the fuel system pressure.
  4. Turn the ignition switch to the OFF .
  5. Remove or disconnect the following:

    Negative battery cable
    Engine covers
    Hose for the Leak Detection Pump (LDP)
    Accelerator pedal cable from the throttle valve control module
    Air guide hose from the throttle valve control module
    Vacuum line from the Evaporative Emissions (EVAP) canister
    Brake booster vacuum hose
    Intake Air Temperature (IAT) sensor and the throttle valve control module
    Camshaft Position (CMP) sensor wiring harness connector
    Fuel rail with the injectors
    Coolant hoses from to the intake manifold
    Crankcase breather hose at the intake manifold
    Intake manifold brace and the oil dipstick
    Manifold at the mounting flange

  6. Clean all gasket surfaces.

To install:

  1. Install or connect the following:

    Intake manifold using new gaskets. Torque the fasteners to 89 inch lbs. (10 Nm).
    Manifold brace. Torque the bolts to 15 ft. lbs. (20 Nm).
    Dipstick
    Crankcase breather and coolant hoses to the intake manifold
    Fuel injector sealing O-ring
    Fuel rail with the injectors. Torque the bolts to 89 inch lbs. (10 Nm).
    CMP and the IAT sensors to the throttle valve control module
    Brake booster and EVAP canister vacuum hoses
    Air guide hose and the accelerator pedal cable to the throttle valve control module
    Hose for the LDP

  2. Top off the engine coolant and bleed, if necessary.
  3. Connect the negative battery cable.
  4. Fully close all power windows to stop, operate all window switches for at least 1 second in the close direction to activate the one-touch opening/closing function.
  5. Check the oil level before starting the engine and top off, as necessary.

2.7L Engines
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine coolant.
  3. Properly relieve the fuel system pressure.
  4. Turn the ignition switch to the OFF .
  5. Remove or disconnect the following:

    Negative battery cable
    Wastegate bypass regulator from fuel rail
    Connector from EVAP canister purge valve
    Connector at turbocharger recirculating valve
    Recirculating valve hose clamps
    Fuel pressure regulator hose clamps
    Exhaust temperature sensors, (leave connected)
    Brake booster hose
    Vacuum reservoir hose
    Connectors for fuel injectors
    Suction hose at turbocharger
    Hose clamps at bypass valve, turbocharger intake line and fuel vapor line
    Fuel rail (4) bolts
    Throttle valve connector
    Air pressure sensor connector
    Pressure hoses at front of engine
    Bypass valve hose
    Intake air temperature sensor connector
    PCV hose
    Fuel return and supply lines to fuel rail
    EVAP valve hose

  6. Remove fuel rail and injectors and support fuel rail
  7. Remove intake manifold

    Click image to see an enlarged view

    Fig. Component view of the intake manifold assembly and related components-2.7L engine


To install:

  1. Installation is the reverse of the removal procedure, using the following torque values:

    Fuel rail bolts: 84 inch lbs. (10 Nm)
    Intake manifold bolts: 84 inch lbs. (10 Nm)


2.8L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Fuel supply and return lines
    Fuel injector electrical connectors and the retainers for the fuel injectors
    Fuel pressure regulator clamp and the regulator
    Fuel manifold
    Injectors
    Any hoses or connectors associated with the intake manifold
    Upper intake manifold mounting bolts
    Upper intake manifold and discard the gasket
    Idle Air Control (IAC) valve
    Exhaust Gas Recirculation (EGR) valve
    Accelerator cable form the throttle body
    Lower intake manifold mounting bolts
    Lower intake manifold

  5. Clean all gasket mating surfaces.

To install:

Click image to see an enlarged view

Fig. Exploded view of the fuel injector assembly-2.8L engine



Click image to see an enlarged view

Fig. Exploded view of the upper/lower intake manifold assembly and related components-2.8L engine

  1. Install or connect the following:

    Lower intake manifold using a new gasket. Torque the bolts to 15 ft. lbs. (20 Nm).
    EGR valve
    Accelerator cable to the throttle body
    IAC valve. Torque the bolts to 89 inch lbs. (10 Nm).
    Upper intake manifold. Torque the short bolts to 89 inch lbs. (10 Nm) and the long bolts to 15 ft. lbs. (20 Nm).
    All hoses or connectors that were removed
    Fuel injectors using new O-rings
    Fuel manifold. Torque the bolts to 89 inch lbs. (10 Nm).
    Pressure regulator and clamp
    Fuel injector retainers
    Electrical connectors
    Fuel return and supply lines
    Negative battery cable


2.8L V6 Engine
  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure.
  3. Disconnect the fuel supply and return lines.
  4. Detach the fuel injector electrical connectors and the retainers for the fuel injectors.
  5. Remove the fuel pressure regulator clamp, then the regulator.
  6. Unbolt and remove the fuel manifold, then the injectors.
  7. Label and detach any hoses or connectors associated with the intake manifold.
  8. Remove the upper intake manifold mounting bolts, then the manifold and gasket.
  9. Remove the Idle Air Control (IAC) valve.
  10. Disconnect the EGR valve.
  11. Disconnect the accelerator cable form the throttle body.
  12. Remove the lower intake manifold mounting bolts, then the manifold.
  13. Clean all gasket mating surfaces of old gasket material.
  14. Place shop rag in the cylinder head openings to prevent dirt and debris from entering the open port.



Click image to see an enlarged view

Fig. Exploded view of the fuel injector assembly-2.8L V6 Engine



Click image to see an enlarged view

Fig. Exploded view of the upper/lower intake manifold assembly and related components-2.8L V6 Engine

To install:

  1. Remove the shop rags from the cylinder head openings.
  2. Install the lower intake manifold using a new gasket, and tighten the mounting bolts to 15 ft. lbs. (20 Nm).
  3. Connect the EGR valve.
  4. Attach the accelerator cable to the throttle body.
  5. Install the IAC valve and tighten the mounting bolts to 84 inch lbs. (10 Nm).
  6. Install the upper intake manifold and tighten the short mounting bolts to 84 inch lbs. (10 Nm) and the long mounting bolts to 15 ft. lbs. (20 Nm).
  7. Attach any hoses or connectors that were removed.
  8. Install the fuel injectors using new O-rings, lubricate the O-rings with a light coating of fresh engine oil, then install the fuel manifold and tighten the mounting bolts to 88 inch lbs. (10 Nm).
  9. Install the pressure regulator and clamp.
  10. Install the fuel injector retainers, and then attach the electrical connectors.
  11. Attach the fuel return and supply lines.
  12. Connect the negative battery cable.
  13. Check and clear any stored fault codes.

3.0L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine coolant.
  3. Properly relieve the fuel system pressure.
  4. Turn the ignition switch to the OFF .
  5. Remove or disconnect the following:

    Negative battery cable
    Engine covers
    Air filter induction tube
    EVAP canister purge valve at air filter housing
    Connector at Mass Air Flow (MAF) sensor
    Air guide hose with MAF sensor
    Air filter housing
    Vacuum hoses at intake manifold change-over valve and check valve
    PCV hose
    Solenoid valve holding plate
    Fuel injector connectors
    Fuel pressure regulator
    Fuel distributor with fuel injectors
    All remaining vacuum and electrical connectors
    Remaining air ducting from throttle body
    Dipstick tube
    Secondary air injection system
    Coolant hoses
    Intake manifold


To install:

  1. Installation is the reverse of the removal procedure, using the following torque values:

    Fuel rail bolts: 84 inch lbs. (10 Nm)
    Intake manifold bolts: 84 inch lbs. (10 Nm)
    All remaining bolts, except M8 on AIR: 84 inch lbs. (10 Nm)
    M8 bolts on AIR system: 17 ft. lbs. (23 Nm)


3.2L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine coolant.
  3. Properly relieve the fuel system pressure.
  4. Turn the ignition switch to the OFF .
  5. Remove or disconnect the following:
    NOTE
    Before removing ribbed belt, mark direction of rotation with chalk or a felt pen. If a used belt rotates in the wrong direction when reinstalled, this can result in breakage. When installing belt, ensure it is correctly seated in the pulleys.


    NOTE
    The air conditioning compressor can only be removed from the bracket with the upper securing bolt still inserted. To accomplish this, press the engine simultaneously to the left side. If necessary, loosen all bolts of the assembly mounting.



    Negative battery cable
    Right and left covers at lock carrier, above main fuse box and coolant expansion tank



    Release tension on belt by screwing an M8 x 40 bolt into bore on tensioning element and remove belt
    Upper mounting bolt for the alternator
    Upper mounting bolts for radiator cowl
    Secondary air hose
    Center and right-hand noise insulation under engine
    Cross piece
    Power steering pump from bracket, hang pump from lock carrier with hoses still attached
    Secondary air injection pump with bracket
    Lower radiator cowl bolts and remove the radiator cowl with fans



    Mounting bolt for air conditioning compressor
    Secure the air conditioning compressor together with the hoses at front longitudinal member (hoses remain connected)
    Alternator
    Oil dipstick tube
    Vacuum reservoir
    Mounting bracket for alternator and air conditioning compressor
    Bolts at front of intake manifold
    Attach puller T10095A or equivalent to ignition coils and remove coils
    Body brace
    Air intake hose
    Crankcase breather hose
    Throttle body
    Hose bracket
    Rear intake mounting bolts, swing intake manifold forward
    Fuel rail with fuel injectors
    Swing back to installed position and remove manifold


To install:

  1. Installation is the reverse of the removal procedure, using the following torque values:

    Intake manifold to cylinder head 115 inch lbs. (13 Nm)
    Bracket for water pump to cylinder block 15 ft. lbs. (20 Nm)
    Intake manifold support to intake manifold 15 ft. lbs. (20 Nm)
    Throttle body to intake manifold 88 inch lbs. (10 Nm)


4.2L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:

    Negative battery cable
    Noise insulation panel
    Intake air grille in bumper
    Accessory drive belt
    Timing belt
    Vacuum line to brake booster unit
    Vacuum line at cruise control module
    Accelerator pedal cable
    Coolant lines to heater core (supply and return to vent valves)
    Left and right knock sensor connectors at fuel rail and remove cable ties (4x)
    Fuel injector harness connectors
    Fuel rail, carefully remove along with fuel injectors, and place down to one side
    Intake manifold


To install:

  1. Install or connect the following:

    Intake manifold. Tighten the fasteners to 15 ft. lbs. (20 Nm).
    Fuel rail. Tighten the bolts to 84 inch lbs. (10 Nm).
    Fuel injector harness connectors
    Left and right knock sensor connectors at fuel rail
    Coolant lines to heater core (supply and return to vent valves)
    Accelerator pedal cable
    Vacuum line at cruise control module
    Vacuum line to brake booster unit
    Timing belt
    Accessory drive belt
    Intake air grille in bumper
    Noise insulation panel
    Negative battery cable


----------------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-start.html

-----------------

Car will not crank?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-crank.html

-----------

Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

-------------

How to troubleshoot car battery?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-car-battery.html

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

car will turn over but will not start?

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html

-----------------

The Brake Indicator Light Stays On dash of car?

http://schematicsdiagram.blogspot.com/2011/06/brake-indicator-light-stays-on-dash-of.html

The ABS and Traction Control Lights stays ON dash of car?

http://schematicsdiagram.blogspot.com/2011/06/abs-and-traction-control-lights-stays.html

Check Engine Light On car?

http://schematicsdiagram.blogspot.com/2011/06/check-engine-light-on-car.html

-------------------------

How to replace Interior Lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-interior-lights-on-car.html

Car lights not working, even after replacing the bulb/lamp?

Click this link below:--

http://schematicsdiagram.blogspot.com/2011/06/car-lights-not-working-even-after.html

---------------

How to replace head lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-head-lights-on-car.html

--------------------

How to replace Parking, turn, and Brake Lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-parking-turn-and-brake.html
How to remove the door panel on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-remove-door-panel-on-car.html

How to replace power window motor in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-power-window-motor-in.html

How to test relays on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-relays-on-car.html

-----------------------------

How to troubleshoot Engine Misfires?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-engine-misfires.html

------------

The spark plug firing order for car?

http://schematicsdiagram.blogspot.com/2011/06/spark-plug-firing-order-for-car.html

------------------------

Where is the Thermostat located in car?

http://schematicsdiagram.blogspot.com/2011/06/where-is-thermostat-located-in-car.html

How to recharge AC on Auto/Truck/car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-recharge-ac-on-autotruckcar.html

-------------------

How to trouble shoot speedometer?

http://schematicsdiagram.blogspot.com/2011/06/speedometer-not-working.html

To Order car parts online:--To get heavy discount on car parts .Click this link below:----

http://technoanswers.blogspot.com/2011/05/from-where-to-order-car-parts-online.html

How to Replace Coil Springs?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-coil-springs.html

How to Replace an Oil Pan Gasket?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html

How to Replace a Fuel Injector

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-injector.html

How to Replace a C.O.P. Type Ignition Coil?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-cop-type-ignition-coil.html

How to Replace a Fuel Pressure Regulator?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-pressure-regulator.html

How to Replace a Fuel Pump?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-pump.html

How to Replace a Rear Lift Gate Locking Mechanism?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-lift-gate-locking.html

How to Clean a Fuel System

http://schematicsdiagram.blogspot.com/2011/07/how-to-clean-fuel-system.html

How to Replace an Ignition Coil

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-ignition-coil.html

How to Replace a Windshield

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield.html

How to Replace a Mass Air Flow Sensor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mass-air-flow-sensor.html

How to Replace a Rear Distance Sensor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-distance-sensor.html

How to Replace a Muffler

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-muffler.html

How to Replace an Engine

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-engine.html

How to Replace an Intake Manifold Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-intake-manifold-gasket.html

How to Replace an Oil Pump

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html

How to Lubricate a Brake Pedal Linkage ?

http://schematicsdiagram.blogspot.com/2011/07/how-to-lubricate-brake-pedal-linkage.html

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

How to Replace a Distributor Cap

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-distributor-cap.html

How to Replace a Door Weather Stripping

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-door-weather-stripping.html

How to Replace a Freeze Plug

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-freeze-plug.html

How to Replace a Head Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-head-gasket.html

How to Replace a Heater Core

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-core.html

How to Replace Spark Plugs?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-spark-plugs.html

How to Replace a Rear Axle Bearing?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-axle-bearing.html

How to Replace a Front Bumper Cover

http://technoanswers.blogspot.com/2011/07/how-to-replace-front-bumper-cover.html

How to Replace a Manual Transmission

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-manual-transmission.html

How to Replace a Headlight Bulb

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

How to Replace a Headlight Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

How to Replace Windshield Wiper Blades

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-blades.html

How to Replace a Cooling Fan

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-cooling-fan.html

How to Replace a Catalytic Converter

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-catalytic-converter.html

How to Replace an Engine Mount

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-engine-mount.html

How to Replace a Fog Light Assembly

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fog-light-assembly.html

How to Change Engine Oil and Filter

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html

How to Replace a Power Seat Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-seat-switch.html

How to Replace a Rear Main Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-main-seal.html

How to Repair a Defroster Grid

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-defroster-grid.html

How to Replace an AWD Transfer Case

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-awd-transfer-case.html

How to Replace a Plastic License Plate Bracket?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-plastic-license-plate.html

How to Replace a Power Seat Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-seat-motor.html

How to Replace Power Steering Fluid

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-steering-fluid.html

How to Replace a Power Window Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-window-switch.html

How to Replace a Quarter Glass Panel?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-quarter-glass-panel.html

How to Pressure Test a Radiator and Cap

http://schematicsdiagram.blogspot.com/2011/07/how-to-pressure-test-radiator-and-cap.html

How to Replace a Radiator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-radiator.html

How to Repair a Hood.

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-hood.html

How to Replace an Energy Absorber

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-energy-absorber.html

How to Replace Heater Core Hoses

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-core-hoses.html

How to Replace a Thermostat.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-thermostat.html

How to Rotate Tires.

http://schematicsdiagram.blogspot.com/2011/07/how-to-rotate-tires.html

How to Replace Wheel Lug Nuts

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-wheel-lug-nuts.html

How to Replace a Tire Valve Stem

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-tire-valve-stem.html

How to Change a Flat Tire

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-flat-tire.html

How to Replace Leaf Springs

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-leaf-springs.html

How to Replace a Heater Control Valve

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-control-valve.html

How to Replace Transmission Cooler Lines

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transmission-cooler.html

How to Replace an Ignition Control Unit

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-ignition-control-unit.html

How to Replace a Brake Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-brake-hose.html

How to Replace a Transfer Case Rear Output Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transfer-case-rear.html

How to Replace a Seat Belt and Seatbelt Retractor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-seat-belt-and-seatbelt.html

How to Replace a Power Steering Rack

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-steering-rack.html

How to Bleed Brakes with a Tool

http://schematicsdiagram.blogspot.com/2011/07/how-to-bleed-brakes-with-tool.html

How to Replace a Tail Light Bulb

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-tail-light-bulb.html

How to Check Automatic Transmission Fluid Level

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

How to Change Automatic Transmission Fluid and Filter

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

How to Replace Vacuum Hoses

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-vacuum-hoses.html

How to Replace an Air Intake Boot

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-air-intake-boot.html

How to Replace a Valve Cover Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-valve-cover-gasket.html

How to Replace a Water Pump

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

How to Replace a Windshield Wiper Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-switch.html

How to Replace Window Run Channel Seals

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-run-channel-seals.html

How to Replace a Window Regulator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-regulator.html

How to Balance a Tire and Wheel

http://schematicsdiagram.blogspot.com/2011/07/how-to-balance-tire-and-wheel.html

How to Replace a Window Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-motor.html

How to Adjust a Hood Release Latch?

http://schematicsdiagram.blogspot.com/2011/07/how-to-adjust-hood-release-latch.html

How to Replace a Radiator Support

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-radiator-support.html

How to Replace a Rear Pinion Seal.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-pinion-seal.html

How to Replace Battery Cables

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-battery-cables.html

How to Replace a Proportioning Valve

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-proportioning-valve.html

How to Replace an Upper Radiator Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-upper-radiator-hose.html

How to Replace a Lower Radiator Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lower-radiator-hose.html

How to Replace a Timing Belt?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-timing-belt.html

How to Check for Loose or Worn Suspension

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-for-loose-or-worn.html

How to Check for Loose Steering System

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-for-loose-steering-system.html

How to Replace an Oil Pressure Switch (Sensor)

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html

How to Replace a Fender Liner or Splash Shield

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fender-liner-or-splash.html

How to Replace a Hood Insulator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-hood-insulator.html

How to Replace a Rear Differential.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-differential.html

How to Repair a Hood Hinge

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-hood-hinge.html

How to Replace a Brake Pedal Return Spring

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-brake-pedal-return.html

How to Replace a Door Shell.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-door-shell.html

How to Replace a Transfer Case Front Output Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transfer-case-front.html

How to Replace a Hood Latch/Lock Assembly

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-hood-latchlock-assembly.html

How to Replace a Lift Gate Strut

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lift-gate-strut.html

How to Replace Mud Flaps (Mud Guards)

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mud-flaps.html

How to Check Differential Oil Leaks and Replace Oil.

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html

How to Replace a Mirror

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mirror.html

How to Replace a Transfer Case Shift Linkage

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-transfer-case-shift.html

How to Replace a Transmission Mount

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-transmission-mount.html

How to Replace a U-Joint

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-u-joint.html

How to Replace a Washer Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-washer-tank.html

How to Replace an A/C Line or Hose

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-ac-line-or-hose.html

How to Replace a Heater and A/C Blower Motor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-heater-and-ac-blower.html

How to Replace an ABS Control Unit

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-abs-control-unit.html

How to Perform a Brake Adjustment

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-brake-adjustment.html

How to Replace an Alternator Belt

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-alternator-belt.html

How to Replace an Emblem

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-emblem.html

How to Replace an Exhaust Manifold Gasket

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-exhaust-manifold-gasket.html

How to Replace a Tail Pipe

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-pipe.html

How to Replace Shock Absorbers

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-shock-absorbers.html

How to Replace a Strut Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-strut-assembly.html

How to Replace a Driveshaft

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-driveshaft.html

How to Replace a Wheel Cylinder

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-wheel-cylinder.html

How to Replace a Hood

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-hood.html

How to Replace a Brake Disc (Rotor)

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-brake-disc-rotor.html

How to Replace a Metal License Plate Bracket

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-metal-license-plate.html

How to Replace a Power Steering Pump

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-power-steering-pump.html

How to Perform a Basic Engine Tune-Up

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up.html

How to Perform a Basic Engine Tune Up-Oil Change

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

How to Perform a Basic Engine Tune Up-Spark Plug and Wire Change

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up_01.html

How to Replace a Distributor Cap and Rotor ?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-distributor-cap-and.html

How to Repair a Valance

http://schematicsdiagram.blogspot.com/2011/08/how-to-repair-valance.html

How to Replace a Turn Signal Switch

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-turn-signal-switch.html

How to Replace a Plastic Bumper Cover

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-plastic-bumper-cover.html

How to Replace a Parking Brake Cable

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-parking-brake-cable.html

How to Replace Windshield Wiper Blade Refills

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-windshield-wiper-blade.html

How to Replace a Corner Light

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-corner-light.html

How to Replace a Bumper Bracket or Side Support

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-bumper-bracket-or-side.html

How to Replace a Washer Pump.

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-washer-pump.html

How to Replace a Grille

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-grille.html

How to Replace a Locking Hub

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-locking-hub.html

How to Replace a Fender

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fender.html

How to Replace a Power Steering Hose

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-power-steering-hose.html

How to Replace a Tailgate

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tailgate.html

How to Replace a Soft Top

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-soft-top.html

How to Replace a Carburetor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-carburetor.html

­

How to Replace a Bumper Trim

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-bumper-trim.html

How to Replace Trunk Strut

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-trunk-strut.html

How to Replace a Front End Cover

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-end-cover.html

How to Replace a Front Pipe

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-pipe.html

How to Replace an Antenna Mast

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-antenna-mast.html

How to Replace a Side Marker Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-side-marker-light.html

How to Install a Carpet on car?

http://schematicsdiagram.blogspot.com/2011/08/how-to-install-carpet-on-car.html

How to Replace a Spoiler

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-spoiler.html

How to Replace a Mirror Glass on car?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-mirror-glass-on-car.html

How to Replace a Step Bumper?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-step-bumper.html

How to Replace a Door Lock

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-door-lock.html

How to Replace a Throttle Body

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-throttle-body.html

How to Replace a Throttle Position Sensor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-throttle-position-sensor.html

How to Replace a Grille Insert

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-grille-insert.html

How to Replace a Fan Shroud Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fan-shroud-assembly.html

How to Replace an Engine Splash Shield

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-engine-splash-shield.html

How to Replace a Turn Signal Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-turn-signal-light.html

How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html

How to Replace a Park Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

How to Replace an Expansion Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-expansion-tank.html

How to Replace an Exhaust System

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-exhaust-system.html

How to Replace a Fender Trim

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fender-trim.html

How to Replace a Headlight Door

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

How to Replace a Fan Shroud

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fan-shroud.html

How to Replace a Harmonic Balancer

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-harmonic-balancer.html

How to Replace a Header Panel

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-header-panel.html

How to Replace a Fuel Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-tank.html

How to Replace a Fuel Tank Cap

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-tank-cap.html

How to Replace a Distributor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-distributor.html

How to Replace an EGR Valve

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-egr-valve.html

How to Replace an Oxygen Sensor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-oxygen-sensor.html

How to Replace an Ignition Wire Set

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-ignition-wire-set.html

How to Replace a Tail Light

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-light.html

How to Replace a Door Handle

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-door-handle_18.html

How to Replace a Hood Strut

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-hood-strut.html

How to Replace Tail Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-light-assembly.html

How to Replace a Front Bumper

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-bumper.html

How to Replace a Fuel Pump Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-pump-assembly.html

How to Replace an Axle Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-axle-assembly.html

How to Replace a Tailgate Handle

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tailgate-handle.html

How to Replace a Wheel Hub Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-wheel-hub-assembly.html

How to Replace a Control Arm

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-control-arm.html

How to Replace a Window Regulator with Motor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-window-regulator-with.html

How to Replace a Headlight

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

How to Check the Brake Fluid Level

http://schematicsdiagram.blogspot.com/2011/08/how-to-check-brake-fluid-level.html

How to Replace a Parking Brake Switch

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-parking-brake-switch.html

How to Replace a Blower Motor Resistor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-blower-motor-resistor.html

How to replace frost plug on car?

http://howtobyme.blogspot.com/2011/08/how-to-replace-frost-plug-on-car.html

Horn stopped working?

http://howtobyme.blogspot.com/2011/08/horn-stopped-working.html

How to clean egr valve on Isuzu Amigo?

http://howtobyme.blogspot.com/2011/08/how-to-clean-egr-valve-on-isuzu-amigo.html

Cruise control stopped working?

http://howtobyme.blogspot.com/2011/08/cruise-control-stopped-working.html

Car is stuck in park and the shift will not move?

http://howtobyme.blogspot.com/2011/08/car-is-stuck-in-park-and-shift-will-not.html

How to change the outer door weather strip?

http://howtobyme.blogspot.com/2011/08/how-to-change-outer-door-weather-strip.html

Car slows down when it gets hotter?

http://howtobyme.blogspot.com/2011/08/car-slows-down-when-it-gets-hotter.html

Warning lights on and speedometer died?

http://howtobyme.blogspot.com/2011/08/warning-lights-on-and-speedometer-died.html

Car won't rev past 1900 rpms?

http://howtobyme.blogspot.com/2011/08/car-wont-rev-past-1900-rpms.html

max