Sunday, September 30, 2012

A/C-HEATER CONTROL CALIBRATION

How to perform A/C-HEATER CONTROL CALIBRATION procedure


The Vehicle is 2006 Chrysler Town & Country.

The Calibration procedure helps many a times during No heat problems.
The heater blows no heat but only cold air.
In such cases the problem is due to faulty Actuator motor or problem with A/C heater control module.
But even after replacing these faulty or weak parts the problem remains the same.
On such cases performing the A/C heater control calibration helps.

The procedure is as follows :----


PLEASE NOTE:----
The A/C-heater control module must be re-calibrated each time an actuator motor or the A/C-heater control is replaced. 
If the vehicle is so equipped, the calibration procedure also includes rear HVAC positions for each actuator motor.

The details are as follows:----

First of all turn the ignition switch to the On position.

There are two types of temperature control systems on vehicle.Manual temperature control system or Automatic temperature control system.

For  manual temperature control (MTC) system, 
  • Press and hold the Rear Wipe/Wash and Re-circulation buttons for at least five seconds. 
The MTC A/C-heater control Rear Wipe/Wash button light emitting diode (LED) and Recirculation button LED, will begin to flash when the calibration procedure has begun.


And with the automatic temperature control (ATC) system, 
  • Simultaneously press and hold the Power and Recirculation buttons on the A/C-heater control for at least five seconds. 
The ATC A/C-heater control Delay and Recirculation graphics will begin to flash when the calibration procedure has begun.

TIME LIMIT:--
The calibration procedure should take less than two minutes to complete for the manual A/C-heater control, and less than twenty seconds for the ATC A/C-heater control. 
When the LEDs or graphics stop flashing, the calibration procedure is complete.

ON Some cases the Flashing light will not stop:---


If the LEDs or graphics continue to flash beyond the two minute (manual) or twenty second (ATC) calibration time.
So here is the problem
These flashing lights indicates that the A/C-heater control has detected a failure and a Diagnostic Trouble Code (DTC) has been set. 
On such cases the vehicle needs to be scanned by OBD tool to retrieve the error codes. These error codes will tell or indicate what part is causing the problem.


IMP NOTE:-- The LEDs or graphics will continue to flash even after the ignition switch is cycled Off and On, until a successful calibration is completed or until the vehicle has been driven about 13 kilometers (8 miles.That flashing is normal.

These details will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

2000 Toyota Avalon: No heat on Passenger Side?

http://whatisbyme.blogspot.in/2012/05/2000-toyota-avalon-no-heat-on-passenger.html

No heat on Oldsmobile Silhouette?

http://technoanswers.blogspot.in/2012/02/no-heat-on-oldsmobile-silhouette.html


Temperature gauge does not move and no heat when heater is ON?

http://technoanswers.blogspot.com/2012/01/temperature-gauge-does-not-move-and-no.html




Dodge Ram 4x4 light keeps flashing

4X4 Low light is Flashing on Dash

The 4x4 Wheel drive low light flashes when shifting and when the shifting is complete the light should go steady  instead of being flashing.

BUT,if the 4WD low light is flashing instead of lit up solid then please check whether the the shift is completed or not OR else  it isn't actually in four low mode. 

YES, its agreed that the switch may have been placed into four low but the shift will not complete unless the correct conditions are met .
The correct procedure to complete the shift in four wheel low drive is place the switch in four low and after that rolling 2-3 MPH with the transmission in neutral. 
Its very common the 4WD light will flash until the correct conditions are met.But once the shift completes then the light will be lit up solid. Only when the light is on solid is it actually in four low. 

AS PER OUR AUTO GARAGE REPAIR EXPERIENCE,

IT SEEMS LIKE .............

The vehicle is actually not got properly engaged in four low, it sounds like the knob is just turned and it didn't shift.
Yes,its very true,this happens many a times.

ABOUT THE PROBLEM OF 4WD low light flashing ,
Either way, as long as it's driving normal and you don't hear any abnormal noises from the engine or drivetrain, and there are no leaks, then you don't have anything to worry about. 

Just dont ignore the issue get regular maintenance /servicing done,if its not done yet.

These basic troubleshooting details should help.
Thanks.

Users Who Viewed This Problem Also Viewed:

Overhead Brake lights not working on 1999 GMC Sierra 4x4?

http://technoanswers.blogspot.in/2012/03/overhead-brake-lights-not-working-on.html



2008 Toyota Tundra: 4x4 Wheel Drive Light is Flashing?

http://technoanswers.blogspot.in/2012/05/2008-toyota-tundra-4x4-wheel-drive.html

4x4 front differential will not engage the axle on ford?

http://technoanswers.blogspot.in/2012/02/4x4-front-differential-will-not-engage.html