Sunday, July 21, 2013

Ford Escape Spark Plug Inspection And Gapping

Ford Spark plug Gapping And Testing

Before going through sparkplug details,its suggested to go through spark plug firing order and wiring diagram.
Click here

Spark Plugs Inspection & Gapping

Sparkplug Inspecting:

  • Check the plugs for deposits and wear. If they are not going to be replaced, clean the plugs thoroughly. Remember that any kind of deposit will decrease the efficiency of the plug. 
  • Plugs can be cleaned on a spark plug cleaning machine, which can sometimes be found in service stations, or you can do an acceptable job of cleaning with a stiff brush. 
  • If the plugs are cleaned, the electrodes must be filed flat. Use an ignition points file, not an emery board or the like, which will leave deposits. The electrodes must be filed perfectly flat with sharp edges; rounded edges reduce the spark plug voltage by as much as 50%.


Sparkplug Gapping:
  • Check spark plug gap before installation. The ground electrode (the L-shaped one connected to the body of the plug) must be parallel to the center electrode and the specified size wire gauge (please refer to the Tune-Up Specifications chart for details) must pass between the electrodes with a slight drag. NEVER adjust the gap on a used platinum type spark plug.


  • Always check the gap on new plugs as they are not always set correctly at the factory. Do not use a flat feeler gauge when measuring the gap on a used plug, because the reading may be inaccurate.
  •  A round-wire type gapping tool is the best way to check the gap. The correct gauge should pass through the electrode gap with a slight drag. If you're in doubt, try one size smaller and one larger. The smaller gauge should go through easily, while the larger one shouldn't go through at all. 
  • Wire gapping tools usually have a bending tool attached. Use that to adjust the side electrode until the proper distance is obtained. 
  • Absolutely never attempt to bend the center electrode. Also, be careful not to bend the side electrode too far or too often as it may weaken and break off within the engine, requiring removal of the cylinder head to retrieve it.


FIG : Inspect the spark plug to determine engine running conditions.
Inspecting Ford Spark Plugs

-----------

Spark Plug Removal & Installation


WARNING
Do not pull on the ignition wire directly, as it may separate from the connector inside the boot.

  1. Disconnect the negative battery cable.
  2. Grasp the spark plug boot firmly and with a twisting-pulling motion remove the spark plug wires from the spark plug.
    NOTE
    If an original spark plug is reused, install it in the same cylinder from which it was removed. New spark plugs can be used in any cylinder.


    NOTE
    Use compressed air to remove any foreign material from the spark plug well before removing the spark plugs.
  3. Remove the spark plugs.
  4. Inspect the spark plugs.

  1. Installation:
    Install a new head gasket and the cylinder head.

    Ford Cylinder Head Bolt Torque Specs

    Fig. Left side cylinder head bolt torque sequence


    Click image to see an enlarged view

    Fig. Right side cylinder head bolt torque sequence
  2. Lubricate the cylinder head bolt threads.
  3. Torque the cylinder head bolts in the proper sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm).
    2. Step 2: Additional 90 degrees.
    3. Step 3: Loosen the bolts one full turn.
    4. Step 4: 30 ft. lbs. (40 Nm).
    5. Step 5: Plus an additional 90 degrees.
    6. Step 6: Plus an additional 90 degrees.

  4. Install or connect the following:

    Hydraulic lash adjusters
    Camshaft followers
    Camshaft
    Exhaust manifold. Torque the bolts in sequence to 15 ft. lbs. (20 Nm), right side only
    EGR tube, right side only
    Coolant bypass tube
    Negative battery cable
  5. Fill the coolant to the proper level.
  6. Start the vehicle and check for leaks, repair if necessary.

    Ford Exhaust Manifold Torque Specs

    Fig. Right side exhaust manifold bolt torque sequence